Search the Community
Showing results for tags 'vlans'.
-
Evening everyone. I'm currently experimenting with setting up a Voip system to replace our old pbx. I've used freepbx at home for a few years so I'm pretty familiar with setting that up, provisioning the phones, dialplans ext... So far I've installed the Distro on an old server, and setup 10 Cisco 7941 phones (in SIP mode) and all is working well. My main concern now is the QoS across the LAN (we will still be using our ISDN lines for external via a Patton Gateway for now). At the moment the call quality between extensions is excellent, however what with the school being almost empty the voice traffic doesn't have much to battle against. Our network has a 1G backbone, and a mixture of 100mb/1G switches (Cisco & HP). We have a number of VLANs across the site. My understanding is that the phones & Asterisk by default (in sip.conf & on the cisco phone status page) add the CoS value (5) and the DSCP code (cs3) to the packets they transmit, so is it a case of making sure 802.1p is enabled on all managed switches? Or is it necessary to setup a new Vlan just for voice and create a trunk between each phone & the switch (tagged voice vlan & untagged data vlan for the pc passthrough)? Any experience of your own way of doing this would be interesting to hear, along with suggestions on the best method in this situation. Many many thanks in advanced!
-
Just introduced VLAN and so far it has been a slow process but all going well so far. There are currently 20 VLANs configured and wondered if those more experienced using VLANs could answer a couple of questions. Quick example - We have IP Phones on our network (on their own VLAN) but not all the edge switches have IP Phones connected to them. Do we need to tag the uplink ports on the core switch those edge switches which do not have IP Phones on them? We are thinking if they are not tagged then there is less traffic to be routed to switches that do not need them. (Does this make sense?) or should we tag all VLANs on all uplink ports? Thanks Mark
-
Hi All, Can anyone help with this please? I have inherited a working Cisco network with VLANS set up by the installer. The edge switches are all Catalyst 2960-S. One stack of switches in our server room seems to be doing something strange compared to all the other hub-room stacks. We have several VLANS set up, but not all are in use yet. The two I have an issue with are: VLAN 301 (PC_Vlan301) and VLAN 410 (VOIP). On the stack in question several ports are showing up on both VLANs at the same time. They are access ports rather than trunks, so I didn't think that was possible. Native VLAN for the stack is the default VLAN 1. If I remove a port or a range of ports from VLAN 410 it also disappears from VLAN 301 and reappears in VLAN 1. When I add it to VLAN 301 it duplicates itself in VLAN 410 automatically. It is almost like the VLANS are linked or are being considered to be the same VLAN even though they have different ID numbers and names. Does anyone know how to unravel this issue? I need to leave all bar five of the ports on the 301 vlan and remove them from the 410 vlan. Thanks in advance
-
I am trying to setup a Vlan At the suggestion of the Line provider for two of our external sites. The lines coming to our server room and straight into a HP Procurve 4108gl i need to give them access to the trunk we have going to another Procurve 4108gl which the other vlans need aceess to also. Then i need them to be able to access several ports off the second Switch along with the other vlans. External----Switch 1----trunk-----switch 2----- servers Hope anyone can help!!! I have tried allsorts of variations of tagged and untagged and forbid ect... And i just cant get it all to flow!! I am at my whit's end here please someone come to my rescue!! Jon
-
I have a flat network with around 700 devices on it. I've never realy got Vlans and how they work and it seemed to add complexity. I know I can offer tagged vlans through my APs but I was once trailing this and my switches started to dissapear so I quit the test. I can't quite get what is going on. It seemed that the second the AP sent tagged traffic the switch it was connected to became unpingable? I hadn't yet configured the switch to do anything? in anycase I have some switches connected to others how do I configure their uplinks so they don't start doing the same an killing large portions of my network. I understand I can set an untagged port on my switch that is infact tagged by the switch instead. I also understand that I need to have different ip ranges on each VLAN? Why for routing? I want them isolated from each other. Only the servers need to see all the traffic so, can send them all the tagged traffic? and not setup multiple DCHP servers / ranges? Does anyone have vlans for dummies?
-
We had 3rd party network support and they set up a lot of our network infrastructure. I have been tasked with taking over this part of the network and have a query about the switch configs re: VLANS. We have three VLANS (two really I guess, the default one plus an 'Internet' VLAN with an ID of 3 and a 'Guest Users' VLAN with an ID of 5.) The switch is set up so that ports 1-24 are untagged for the default VLAN, ports 1-24 are all tagged for the Internet VLAN (3) and also tagged for the Guest Users VLAN (5) Sorry for the noob question, but what are the implications of having this config? I know next to nothing about VLANS but it seems that doing it like this defeats the object of having a VLAN in the first place? I really could do with an idiots guide to VLANS as it is one area that I am woefully ignorant about. If the above config is fine and I want to add another switch, I would presumably just set the VLANS up in the exact same way? Thanks
-
Hi folks Bit of advice, we currently have a vlan segmented network consisting of 6 HP switches and 1 cisco switch in 2 locations. The Hp switches are all configured for Intervlan routing, we have the following vlans. Admin, Voip, Wireless Access, Guest Wireless, Curriculum and Security. It is a brand new school configured by sub contractors as part of the new build. Everything works fine, and all devices get there correct ip address from our server. We are about to move to a new internet provider, they have given us a range of Ip Addresses for us to use, I have just found out today, with no consultation that the 3rd party provider who are going to facilitate the move has decided to flatten the entire network, and to secure the admin side devices with dhcp reservations . Currently we have about 140 devices connected to the network, including wifi access points, cctv, electronic doors, voip phones and a guest network, all on its own vlans. What are the advantages and disadvantages of the flattening of the network ? Many Thanks. Casa
-
Hi All, I'm looking for some help with a strange issue I currently have - my network setup as follows: Client>>>>HP Switch>>>>Lightspeed>>>>Router Vlan 1 - Default Vlan (Client Default gateway address is 10.18.168.1) Vlan 40 - Guest BYOD (Client Default gateway addess is 10.19.72.2) >>>10.19.72.2 is the Vlan 40 IP address. Vlan 60 - Staff BYOD (Client Default gateway address is 10.19.88.2) >>>10.19.88.2 is the vlan 60 IP address. I have a static route set on the main switch for the default gateway 10.18.168.1 - so everything that cant find its way out goes to 0.0.0.0/0 then the static route forwards it to 10.18.168.1 (the router) The problem is any users on Vlan 40 or 60 do not seem to be getting filtered by the lightspeed, so users can access any website. I have contacted lightspeed but they seem to think the tagged traffic is not hitting the lightspeed? Does anyone have any ideas, I have tagged the port 4/12 with vlan 40 that goes out the lightspeed but it doesn't make any difference (the lightspeed is working as a bridge)? I'm just trying to get vlan 40 to work so far. Here is the running config of the switch and router below: HP Switch>>>>> Running configuration: ; hpStack_WB Configuration Editor; Created on release #WB.15.11.0007 ; Ver #03:12.15.0d:09 stacking member 1 type "J9728A" mac-address 6cc217-0b6c00 member 2 type "J9728A" mac-address 1458d0-9b22c0 member 3 type "J9728A" mac-address 6cc217-0b9cc0 member 4 type "J9728A" mac-address 1458d0-9be100 exit hostname "HP-Stack-2920|ITWorkshop|CabA" trunk 2/A2 trk1 trunk trunk 2/A1 trk2 trunk banner motd timesync sntp sntp unicast sntp server priority 1 10.18.168.13 sntp server priority 2 86.19.119.81 no telnet-server web-management ssl ip access-list extended "vlan40filter" exit ip access-list extended "vlan60filter" exit ip default-gateway 10.18.168.1 ip dns server-address priority 1 10.18.168.13 ip route 0.0.0.0 0.0.0.0 vlan 1 ip routing interface 2/19 name "Internet Out - LightSpeed" speed-duplex 100-full exit snmp-server community "public" unrestricted oobm ip address dhcp-bootp member 1 ip address dhcp-bootp exit member 2 ip address dhcp-bootp exit member 3 ip address dhcp-bootp exit member 4 ip address dhcp-bootp exit exit vlan 1 name "DEFAULT_VLAN" no untagged 2/21,2/23-2/24 untagged 1/1-1/8,1/10-1/48,1/A1-1/A2,1/B1-1/B2,2/1-2/20,2/22,2/25-2/48,2/B1-2/B2,3/1-3/4 8,3/A1-3/A2,3/B1-3/B2,4/1-4/48,4/A1-4/A2,4/B1-4/B2,Trk1-Trk2 tagged 1/9 ip address 10.18.171.2 255.255.252.0 exit vlan 40 name "Student + Guest BYOD" untagged 2/21,2/23-2/24 tagged 1/43,2/19,4/9,4/11-4/13,4/15,4/19,Trk1-Trk2 ip address 10.19.72.2 255.255.248.0 ip helper-address 10.18.168.13 ip helper-address 10.18.168.14 exit vlan 60 name "Staff BYOD" tagged 1/43,4/9,4/11,4/13,4/15,4/19,Trk1-Trk2 ip access-group "vlan60filter" vlan ip address 10.19.88.2 255.255.252.0 ip helper-address 10.18.168.13 ip helper-address 10.18.168.14 exit spanning-tree Trk1 priority 4 spanning-tree Trk2 priority 4 no autorun no dhcp config-file-update no dhcp image-file-update password manager HP Router >>>>>>>>>>>> interface GigabitEthernet0/1 description LAN bandwidth 1000000 no ip address ip verify unicast reverse-path duplex full speed 100 ! interface GigabitEthernet0/1.1 bandwidth 1000000 encapsulation dot1Q 1 native ip address 10.18.171.254 255.255.252.0 ip access-group LAN-to-LAN in ! interface GigabitEthernet0/1.40 bandwidth 1000000 encapsulation dot1Q 40 ip address 10.19.79.254 255.255.248.0 ip access-group LAN-to-LAN in ! interface GigabitEthernet0/1.60 encapsulation dot1Q 60 ip address 10.19.91.254 255.255.252.0 I'm not sure where I'm going wrong here? Could someone post me there HP switch & router config if you have the same setup please? Any help would be great. Thanks Al
-
- hp switch
- lightspeed
-
(and 1 more)
Tagged with:
-
Hello folks, I will have some chromebooks and ipads on the network this year and need to add / expand my dhcp scopes and vlans to accommodate them. I have dynamic vlans setup with the radius server, so depending on your username / group membership you get a different vlan. Currently that is staff, student, ipad for school owned devices. The ipads currently connect with one generic username. I am considering splitting this into three user accounts, and doing the same for the chrome books. This would potentially allow each device group to get its own subnet, allowing me to apply content filtering at the building level. I am considering 9 smaller vlans , or 3 larger ones. ES chrome, ES Ipad, ES Students (Domain laptops / netbooks); none at this time. MS chrome, MS Ipad, MS Students (Domain laptops / netbooks) HS chrome, HS Ipad, HS Students (Domain laptops / netbooks) OR ES students, MS Students, HS Students What are the pros and cons for either of these scenarios? Thanks,
-
Hey Guys, We are in the process of overhauling our Wifi network. In order to accommodate all the new Unifi APs, we are wanting to create VLANS on our switches with a different subnet for the APs. We use HP switches across the site, with a ProCurve E5406 at the core, and mainly ProCurve 2650s in all the other cabs. How do i set up the VLANS on them, and how do i set up a subnet in DHCP? Our current flat network uses a 172.25.16.0/22 CIDR subnet, would i use this for the VLAN or would i need a whole new subnet? I hope this is clear enough, I have no experience with VLANS or subnetting. Any help is greatly appreciated. Thanks! Regards Harry
- 7 replies
-
- subnetting
- switch config
-
(and 3 more)
Tagged with:
-
Hello All, We recently split up our network up into 7 separate vlans due to a shortage of ip addresses. A new core switch (HP E5406ZL ) has been installed which seems to work effectively however I cannot seem to get the WDS (Server 2008 R2) working again. The subnets are as follows - 10.122.192.--- 10.122.193.--- 10.122.194.--- 10.122.195.--- 10.122.196.--- 10.122.197.--- 10.122.198.--- All the servers (DNS,PDC,WDS etc) are on the same subnet (10.122.196.) Can any one help?
- 16 replies
-
- hp e5406zl
- server 2008 r2
-
(and 2 more)
Tagged with:
-
Hi all, We have a network of about 1000 machines, combined pc's and laptops. We have just added wireless access points and want to direct all wireless traffic straight to our proxy server and out onto the internet, without any risk to our servers or security. Have been advised to use VLANs but no experience in them at all in the department. We run windows 2003 server on a few different servers and the switches which connect the AP switch to the server are a Procurve 2650 and a 3Com 2226. Could anyone please give some advice on whether VLAN is the best idea, and how would I go about starting with it... Thanks for your thoughts.
-
Hi all, We have a HP 1810-48G switch as a core switch which is connected to a Cisco router which has been configured with two VLANs. I'm pretty new to VLANs but when I have previously set them up I have set up the VLANs and then configured the subinterface address/gateway for said VLANs. However on this switch it allows me to create the VLAN IDs with no further configuration. Am I missing something obvious, how do I setup this switch correctly. Thanks for any help Tom
- 2 replies
-
- 1810-48g
- networking
-
(and 2 more)
Tagged with:
-
Hi all, I’m looking for some help with a slow DHCP problem. We’re using mac-based authentication, procurve switches and IAS. 30 vlans dynamically allocated, the 30 subnets managed by server 2008 DHCP. Everything works fine except DHCP is slow, not hideously slow, but can be 10 to 30 seconds or so. This was never a real problem and got put on the back burner; but we’re now running a few thin clients which ask for an address twice during boot (one for pxe, one for the thinclient os) and so its time to pin it down. In a nut shell, If a machine is put in a vlan dynamically then DCHP is slow. If the same machine is forced (port untagged) into a vlan then DHCP works as it should. IAS validates the machines immediately so the delay isn’t there (dhcp is slow even if I randomly /release /renew after a while). There’s nothing obvious shouting out of the DHCP logs – though I haven’t been through them with a fine tooth comb. I’ve had a Google around and nothing stands out. DMcCoy, I think we have a similar setup to you; did you experience anything like this? Anyone got any ideas? Edit: just found a slightly later firmware for the 2626’s (the changes log doesn’t mention fixing a dhcp problem but you never know…), I'll try that on monday...
- 3 replies
-
- 8021.x
- mac authentication
-
(and 3 more)
Tagged with:
-
Hi, Im a noob to VLANs and I am having some trouble getting my head around it. Any help would be great, thank you in advance. I have HP Procurve switches 5412zl in the core and 2650 on the edge. I have setup vlans between switches without any problems. I also have DHCP serving IP Addresses within both VLANs. My setup: default VLAN(1) - IP Range 10.2.104.0/21 second VLAN(11) - IP Range 192.168.4.0/22. My default gateway is 10.2.111.254, how can I get VLAN(11) to access the internet/default gateway? Here is part of running configuration of the 5412zl: ip routing ip irdp timesync sntp snmp-server community "public" Unrestricted vlan 1 name "DEFAULT_VLAN" untagged A1-A23,B1-B24,C1-C24,D1-D24,E1-E24,F1-F4 ip address 10.2.111.210 255.255.248.0 no untagged A24 ip igmp exit vlan 11 name "CURRIC_WRC" untagged A24 ip helper-address 10.2.104.1 ip address 192.168.4.1 255.255.252.0 tagged A12,D5,D7,F2 exit ip route 0.0.0.0 0.0.0.0 10.2.111.254 spanning-tree
-
Do you multihome your servers into all your VLANs, or do you have a dedicated server VLAN and route all the traffic?
-
I recently wanted to see if I could educate Linux about VLAN tagging and dispense with the multiple network card approach we've used in the past. Mainly because it's more elegant and I loath wasting hardware and Gigabit switch ports when I don't need to. Happily it worked, so here's how I did it. Disclaimer: These instructions work for Ubuntu 6.06 LTS. If your using another distro (specifcally something not based on debian) these instructions wont work. However they should point you in enough of the right direction to get it going. Prequesites VLAN support is actually a kernel feature, if you don't have it compiled it, it's not going to work. Check this before you continue. For reference, I'm using the 'linux-server' meta package on Ubuntu, which does support this. If your doing a kernel compile, the option that enables 802.1Q VLAN support is found under the Networking options. You also need the usermode configuration tool 'vconfig'. This is avalible in the package 'vlan' on debian based distros. So simply apt-get it. If you can't use this package you can get the source and compile it yourself from here. The vlan package also installed some configuration scripts that hook into the standard network interface ifup/ifdown scripts. If your not using the vlan package, you'll have to cook up your own. Switch Configuration Obviously the machine will needed to be plugged into a port on a switch that supports VLANs. This usually means using one of the more expensive managed switches. Unfortunately I can't give instructions for every possible switch that supports VLANs so I'll just give a generic overview and a specific example using a ProCurve 2650 via its console (its inadvisable to configure VLANs via telnet or the web interface, if you get something wrong you're likely to lose access to the switch). Generally on switches supporting VLANs there are two configuration areas related to them. A global configuration that assigns numeric VLAN IDs to some easily recognizable name. So for example you might have: VLAN ID 1 = DEFAULT_VLAN (*) VLAN ID 2 = CURRICULUM VLAN ID 3 = ADMIN * VLAN 1 is special. It's the only VLAN that will let you communicate with the switches management interface. Thus it's best not to use it other than for infrastructure management. Once the VLANs are configured you can assign them to specific ports on the switch. There's three possible states for a port for each VLAN. Untagged member Any data traveling over this port with no VLAN information attached will be tagged with this VLAN ID. You generally use this when you have a device that isn't configured for VLANs and you only want it to be a member of one VLAN. A end client PC for example. Tagged member Data travelling over this port with VLAN information attached for the VLAN ID listed as a tagged member will be forwarded on. Any data with no VLAN information attached (untagged as above) or VLAN IDs that have not been configured for use with the port will be dropped. Non-member The port isn't a member of this VLAN. It will never get any data sent using the VLAN ID. Configuration of the ProCurve The ProCurves have a lot of extra features when it comes to VLANs. However I'm only going to show the basics here. Firstly I log into the switch and enter the configuration context. ProCurve J4899B Switch 2650 Firmware revision H.08.98 Copyright (C) 1991-2006 Hewlett-Packard Co. All Rights Reserved. RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subdivision (b) (3) (ii) of the Rights in Technical Data and Computer Software clause at 52.227-7013. HEWLETT-PACKARD COMPANY, 3000 Hanover St., Palo Alto, CA 94303 We'd like to keep you up to date about: * Software feature updates * New product announcements * Special events Please register your products now at: [url]www.ProCurve.com[/url] Password: ******* ProCurve Switch 2650# configure Once this is done. I can configure my VLANs name ProCurve Switch 2650(config)# vlan 2 name CURRICULUM ProCurve Switch 2650(config)# vlan 3 name ADMIN That was easy! Now on to configuring the ports. For this specific switch we want the untagged member for all ports to be VLAN 2. On most switches we'd have to go through all the ports and set each one. However there's a nice shortcut on procurves to do this quickly for all ports. ProCurve Switch 2650(config)# primary-vlan 2 Ports 49 and 50 are special though. They are Gigabit uplinks to other switches. Thus we don't really want to have untagged data floating about and having the switch at the far end 'guess' what it's supposed to do with it. We also need to add VLAN 1 ( the management VLAN) so we can remotely admin the switch. ProCurve Switch 2650(config)# vlan 1 tagged 49 50 ProCurve Switch 2650(config)# vlan 2 tagged 49 50 ProCurve Switch 2650(config)# vlan 3 tagged 49 50 So now, we have a functional switch that understands our networks VLANs and does the 'right thing' by default. Now for the purposes of this HOWTO, our Linux base server is going to be in port 10. We want it to communicate on both VLAN 2 and 3. So we have a couple of options here. We can either just add port 10 as a tagged member to VLAN 3 and leave untagged data going to VLAN 2. Or we can set port 10 to be a tagged member of both VLAN 2 and 3. Personally I find this second option to be more understandable (especially from Linux). However I'll provide examples for both here and later in the Linux section. Option A: Mixed tagged and untagged port. By default the swtich will send untagged data out on VLAN 2 so we don't have to do anything about it (see above). ProCurve Switch 2650(config)# vlan 3 tagged 10 Option B: Explicit tagged port You'll notice this is exactly what we did for our uplink ports (Minus the management VLAN). ProCurve Switch 2650(config)# vlan 2 tagged 10 ProCurve Switch 2650(config)# vlan 3 tagged 10 You will lose connectivity to your Linux machine at this point if you went for Option B Debian based distro configuration For host configuration, we also need to know the ip addressing schemes being used. For the purposes of this HOWTO. We shall assume that the CURRICULUM VLAN is using hte address range 192.168.200.0/24 and the Linux machine has been assigned the address 192.168.200.10. The default router is 192.168.200.1 for this network. We shall assume the ADMIN VLAN is using the address range 192.168.300.0/24 and the Linux machine has been assigned the address 192.168.300.10. We will not use the router available on this VLAN. On debian based systems. The init scripts for networking control the VLAN assignment for interfaces. They require that a virtual interface is created for each VLAN the system will be a member of. This is done by naming the interface as 'vlanXX' (where XX is the VLAN ID) in /etc/interfaces/networks. Additionally each VLAN interface must be assigned to a physical interface with the 'vlan_raw_device' keyword. Configurations wil differ at this point depending on if you chose to use Mixed or Explicit port tagging. Option A: Mixed Tagged Port In this configuration, the default network interface will be used to generate untagged traffic. So eth0 can be configured as normal Additionally a vlan3 interface must be configured to generate tagged traffic for VLAN ID 3 (ADMIN). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 192.168.200.10 netmask 255.255.255.0 gateway 192.168.200.1 # VLAN interface for ADMIN (VLAN 3) auto vlan3 iface vlan3 inet static address 192.168.300.10 netmask 255.255.255.0 vlan_raw_device eth0 Option B: Explicit Tagged Port In this configuration, the default network interface will left un-configured. The vlan2 interface will be configured to generate traffic for VLAN ID 2 (CURRICULUM). The vlan3 interface configuration is identical to before. # The loopback network interface auto lo iface lo inet loopback # VLAN interface for CURRICULUM (VLAN 2) auto vlan2 iface vlan2 inet static address 192.168.200.10 netmask 255.255.255.0 gateway 192.168.200.1 vlan_raw_device eth0 # VLAN interface for ADMIN (VLAN 3) auto vlan3 iface vlan3 inet static address 192.168.300.10 netmask 255.255.255.0 vlan_raw_device eth0 Astute readers will now realise why I prefer this second method. The interface names make it very obvious which interface is associated with which VLAN. Finishing Up You can either reboot or run '/etc/init.d/networking restart'. Just be aware that existing network services will also need restarting to pickup the changes if you only restart networking. Once everything is back up and running, you can verify the new network interfaces are configured correctly. You can do this either with 'ifconfig' or you can examine the contents of the files in '/proc/net/vlan'. The 'config' file lists vlan to physical interface mappings and each 'vlanxx' file lists VLAN specific statistics.
-
Ok my situation is this, we are setting up a wireless extension of our network through radio's and We can extend our 1.1 network over to the new location and that will give us data for our computers, but the confusion comes here. we have a phone system that is on our 2.1 network at the base and I wanted to know how could I possibly set up a vlan over the radio link for the phone system when I can't physically plug a ethernet cable into the tagged port since I will already have the radio plugged into the 1.1 network port. How do I get the phone traffic over to the other location also? I know I may not be making this clear, but I just need to know can we route from our switch at the base and be able to extend the phone network with the data network. The radio links are just a wireless ethernet cable they will transport the ip address coming off our main switch and send it over to the new building in the new switch, can we still use our phones as if we are still on the base network switch? I'm including a mini Diagram to give you some type of idea of how the radio links will work Radios.pdf Radios.pdf
- 2 replies
-
- extended network
- network configuration
-
(and 3 more)
Tagged with:
-
I put this in networks as I feel the problem is in my network somewhere but I cannot find the source of the issue. Long story short I set up a MacOS server running OS 10.10 and profile manager and all the goodies to manage a lab of macs we are deploying. Everything seems to work until I move a mac to a different subnet/vlan. I know certain ports need to be open for traffic to communicate and I do not see any reason why I would have ports 2195, 2196, 5223, 1640 blocked on internal traffic. In some reading on the internet I found that a IP Helper statement for the IP of the MacServer is needed on each VLAN for some traffic to communicate so I set that up on my core switches too (I do not think I need it on the endpoint switches) My network is primarily HP ProCurve based with some cisco switches thrown in for our Wireless. All the managed macs will be wired (at least at this point) but if I can get this to work we may use it for the handful of MacBooks we have assigned to some teachers. I am curious what I can check to see if the desired ports are opened and test communication for pushing profile settings across subnets. If I can get the Macs to Netboot and image across subnets too that is just an added bonus.
-
- mac os
- profile manager
-
(and 1 more)
Tagged with:
-
Ok strange problem, not sure what else to look at. A pc which sits in vlan3 doesn't get the correct IP from the dhcp server. It's gets one from vlan1 Vlan 3 has its own range on the dhcp server. DHCP servers gateway is set to vlan 1 ip 10.35.248.130 A manual IP from the van 3 range for that pc lets you ping the gateway (layer 3 hp switch) Also lets you ping its own gateway (ip address for the vlan on the hp switch) The IP helper address is set to the dhcp server which sits in vlan 1 All the other vlans work correctly. Any help would be great as i can’t work this out. Config from layer 3 switch Running configuration: ; J8698A Configuration Editor; Created on release #K.15.16.0004 ; Ver #06:74.fc.7f.ff.3f.ef:de hostname "Core-01" module 1 type j9534a module 2 type j9536a module 3 type j9534a module 4 type j9534a module 5 type j9550a module 6 type j9550a module 7 type j9550a module 8 type j9546a module 9 type j9550a module 10 type j9550a module 11 type j9538a module 12 type j8706a fault-finder broadcast-storm sensitivity high fault-finder bad-driver sensitivity high fault-finder bad-transceiver sensitivity high fault-finder bad-cable sensitivity high fault-finder too-long-cable sensitivity high fault-finder over-bandwidth sensitivity high fault-finder loss-of-link sensitivity high fault-finder duplex-mismatch-hdx sensitivity high fault-finder duplex-mismatch-fdx sensitivity high fault-finder link-flap sensitivity high trunk E24,F24,G24 trk1 trunk trunk B21,K8 trk2 trunk trunk J19-J20 trk3 trunk trunk J21-J22 trk4 trunk trunk J23-J24 trk5 trunk trunk G19-G21 trk10 trunk timesync sntp ip default-gateway 172.16.100.1 ip directed-broadcast ip route 0.0.0.0 0.0.0.0 172.16.100.1 ip route 172.16.0.0 255.255.255.0 172.16.0.1 ip routing ip udp-bcast-forward interface B20 name "ICT Office Uplink" exit interface E1 lacp active name "Printers" exit interface E2 lacp active name "Printers" exit interface E3 name "Printers" exit interface E4 name "Printers" exit interface E5 name "Printers" exit interface E6 name "Printers" exit interface E7 name "Printers" exit interface E8 name "Printers" exit interface E9 name "Printers" exit interface E10 name "Printers" exit interface F1 lacp active exit interface F2 lacp active exit interface G1 lacp active exit interface G2 lacp active exit interface G5 name "Internet" exit interface J19 name "Trunk to Edge 01" exit interface J20 name "Trunk to Edge 01" exit snmp-server community "public" unrestricted snmp-server host 10.35.248.45 community "public" snmp-server host 192.168.100.51 community "public" snmp-server location "Server Room" vlan 1 name "DEFAULT_VLAN" no untagged B18,B20,F1-F23,G5 untagged A9-A24,B1-B17,B19,B22,C1-C24,D1-D24,E1-E23,G1-G4,G6-G18,G22-G23,H1-H8,I1-I24,J1-J18,K1-K7,L1-L24,Trk1-Trk5,Trk10 tagged A1-A8 ip address 10.35.248.130 255.255.252.0 ip forward-protocol udp 10.36.15.255 7 ip forward-protocol udp 10.36.15.255 9 ip igmp exit vlan 2 name "WLAN_CLt" tagged A1-A8,B22 ip address 10.36.0.1 255.255.248.0 ip helper-address 10.35.248.41 exit vlan 3 name "Wired_Clt" untagged B18,B20,F1-F23 tagged A1-A8,E23,K1-K7,L1,Trk1-Trk5,Trk10 ip address 10.36.8.1 255.255.248.0 ip helper-address 10.35.248.41 ip igmp exit vlan 5 name "SPC_IPADS" tagged A1-A8,B22 ip address 10.36.16.1 255.255.248.0 ip helper-address 10.35.248.41 exit vlan 6 name "Sixthform_Wifi" tagged A1-A8,B22 ip address 10.36.24.1 255.255.248.0 ip helper-address 10.35.248.41 exit vlan 11 name "Internet" tagged A1-A8,E23,K1-K7,L1,Trk1-Trk2,Trk10 no ip address exit vlan 12 name "Internet_GW" untagged G5 tagged A1-A8,E23,K1-K7,L1,Trk1-Trk2,Trk10 ip address 172.16.100.2 255.255.255.0 exit vlan 13 name "Mgmt_AP" untagged A1-A8 tagged E23,K1-K7,L1,Trk1-Trk2,Trk10 ip address 172.16.101.1 255.255.255.0 ip helper-address 10.35.248.41 exit vlan 41 name "Guest" tagged A1-A8,B22,E23,K1-K7,L1,Trk1-Trk2,Trk10 ip address 172.16.0.1 255.255.248.0 ip helper-address 10.35.248.41 exit spanning-tree Trk1 priority 4 spanning-tree Trk2 priority 4 spanning-tree Trk3 priority 4 spanning-tree Trk4 priority 4 spanning-tree Trk5 priority 4 spanning-tree Trk10 priority 4 no spanning-tree bpdu-throttle no autorun no dhcp config-file-update no dhcp image-file-update password manager password operator Edge ; J9280A Configuration Editor; Created on release #Y.11.44 hostname "Edge-02" trunk 43-44 Trk4 Trunk snmp-server community "public" Unrestricted snmp-server host 10.35.248.45 "public" snmp-server host 192.168.100.51 "public" vlan 1 name "DEFAULT_VLAN" untagged Trk4 ip address 10.35.248.132 255.255.252.0 no untagged 1-42,45-48 ip igmp exit vlan 3 name "Wired" untagged 1-42,45-48 tagged Trk4 exit gvrp no stack spanning-tree Trk4 priority 4 Many thanks
-
Hi all, Not necessarily a wireless question, but certainly related... Just curious how folks are segmenting their networks and what that segmentation is used for? And what mechanism you are using for access/vlan assignments, particularly on wireless? wireless vs wired faculty vs students vs guests personal vs school-owned QoS/bandwidth throttling ACLs/network security - what are you protecting? Looking forward to hearing what people are doing! Thanks!
-
Hi all, I'm asking here because I can't get an answer out of the manufacturer. I'm installing IP CCTV very soon. Cabling is already done with CAT6. Was looking at Axis dome cameras and an NVR. I have POE switches in all locations and will be running this on a separate VLAN. Anyone have any experience of Axis with NVR's. a) Do Axis cameras support VLANS? b) Will they run with POE from a switch? (I've read that some brands of camera won't, even being POE capable, and require a separate power injector) c) Any recommendations of brands of NVR that supports Axis cameras? (16 channels) Any (simple) advice on configuring the VLAN (have Cisco POE smart switches connected to Netgear L2 and L3 switches) Cheers in advance ; )
- 9 replies
-
- cctv
- ip cameras
-
(and 3 more)
Tagged with:
-
This should be a simple issue to address but I can't seem to make it work. Scenario Two subnets: 10.20.30/22 behind a HP 3500 switch connected to 192.168.1/24 subnet. The 3500 switch has two VLANs. VLAN2 has IP 10.20.28.1 containing ports 1 - 23 all untagged. VLAN1 has IP 192.168.1.250 and is just port 24 (fibre) untagged. Port 24 (fibre) on the 3500 is the uplink to a HP 2910 switch on port 28. All ports untagged in one VLAN. There is another 2910 switch uplinked via copper from the first 2910, all ports untagged on one VLAN. These 2910 switches carry 192.168.1/24 subnet clients. Internet gateway appliance is 192.168.1.1 linked to the first 2910 switch. I need two-way communication between all devices in both subnets and for all devices in the 10.20.30/22 to be able to access the Internet via 192.168.1.1 gateway. The aim is for the 10.20.30 subnet to host all DNS and DHCP + file storage. Most clients and all legacy servers will remain in the 192.168 subnet but they obviously need to be able to obtain DN resolution and DHCP from the 10.20.30 subnet devices. I have tried many configurations using IP Helper addresses, static routes etc but I cannot get the clients on 192.168 to see the DHCP or DN servers on 10.20.30. Neither can I get devices on 10.20.30 to get to the internet. Neither can I get server - client access from 192.168.1 to 10.20.30 Curiously I can ping and tracert the gateway but not access it in a meaningful way. What do I need to reconfigure on the 3500 and / or 2910 switches in order to get cross-VLAN traffic running freely?
- 13 replies
-
- hewlettpackard
- networking
-
(and 2 more)
Tagged with:
-
Hi all, I'm looking at setting up a couple of VLAN's to separate out staff & pupil machines and CCTV. Have I got the correct hardware in place and how do I do it? 2 x Netgear GSM7312 L3 Switch (I'm currently using these to connect 2 buildings together via fibre. 1 at router end, 1 remote) 1 x Netgear GSM7224 L2 Switch Loads of smart switches in the classrooms and offices. My DHCP server is virtual in a quad ethernet port host server Do my classroom switches need to be VLAN configurable or just the L3 switch? Confused..
