ITGURU

I have disconnected the RJ11 on case its causing an issue but no change in speed. Definitely not ISP issue as full speed with the supplied EERO router. Draytek is on latest firmware however it I'd the BT version as on BT broadband so wonder if that's any reason for it. However if I change the firmware back to the generic is might then cause issues with the Vdsl side when fail overs as the BT version is recommended for vdsl

I am with YouFibre.

I have a Draytek 2865 router which has a direct VDSL RJ11 port for existing broadband (WAN1) Have just got FTTP installed (1 gig) and using the WAN2 Port for this connection - ultimately for FTTP (wan2) as primary and WAN1 (VDSL) is set as failover/backup When i connect direct to the supplied router, i get speeds of 900+ down and up. However, when I connect the NTE to the Draytek and do a test, i don't get much above 500Mb/s . Is this limitations of the router hardware even though the ports and all devices are hardwired gigabit.?

Should always have at least 1 x physical domain controller so you have a domain/can restore a domain before other systems including backup severs if they are domain joined!

Needs more than software these days, most school work is online now so next they'll be complaining they cannot do their work, so up to teachers to enforce rules and if need be escalate up for behaviour. Locking PCs, blocking students access isnt going to stop them misbehaving. We find students on game sites every day, as soon as you are asked to block their access or block one site, there will be another .

Thanks, have now blocked the download and urls so hopefully wont be any more instances.

We run the basic version of malwarebytes which scans machines daily and reports and detections. We're seeing an increase in the number of WAVE BROWSER detections. Its proving difficult to find out how/why we are receiving these. Speaking to the users they say they've not noticed anything different , but can only take their word for it. Not sure if anything else has had this, or how I can find the source at the exact time as doesnt report immediately,

D-Link with controller or Ubiquiti Unifi at our sites. Set it and forget it never any issues and one off costs, no subscriptions required.

No, but unless 365 lost all our data at the same time as the above happening, then its not an issue. Synology would be used to recover compromised mailboxes/lost mail, if synology lost then just resync the data.

Using on-site Synology with backup for 365 all free apart from obvious cost of hardware/drives.

Wondered if someone could shed some light on what I could possibly be doing wrong. I have hyperv hosts and the VMs replicated to replica servers. Everything works fine, status shows as Normal etc etc However, whenever I go to update the host or replica servers, I PAUSE the replication. I used to just reboot the servers but then found after a reboot, replica status would show as critical and thought its because I didnt pause it first, however is not the case. Again this evening I paused the replication between primary and replica server, rebooted the replica server, and 3 of the 4 VMs when i selected resume replication show as critical status, only one of them has gone back to NORMAL. What am i missing? Everytime i have to remove the replica, delete it and then do a full copy of the VM to the replica again, until next time i reboot!

We just buy the hardware and configure/install in-house. cost effective and great support from the vendor.

VNC/RDP locked down to source admin PC IPs that can remote in.

sorry to bring up an old thread! However i'm 99% there with getting RDweb working through azure proxy and wondered if someone could help me please, who has it successfully working So far - I can go to the https:// msappproxy url and authenticate via office 365 - i get the local server rd login page and the user can login successfully - i click on an APP ,in the html web client - i get the error below. not sure where I need to check/change settings or what to check? I've followed multiple online guides of which all seem to be all part of the step by step required.

Does anyone have the step by step guide they followed for setting up publishing of RDWEB through Azure Application proxy? I've followed the online guides and when i got to the msappproxy.net url i get the default IIS page. However, as soon as I put the rdweb on the end, I get a part page load with just the name of the site and nothing else shown below. please could anyone assist? thanks in advance,

Thank you. that was it. The user didn't have a license on 365 and has now synced without issue misleading error message

Yes just check - email field in AD shows correct public domain and attribute editor shows same addresses as the screenshot above. Guess will be a case with MS

The accounts have the UPN as the full public domain name/email address in AD If i look in local Exchange ECP and open both accounts (a working and non working) i see all the same domains shown on each account as per the screenshot above of the 2 accounts.. Where else should i look for any differences?

I'm currently migrating mailboxes from local exchange to office 365. Imported csv file of mailboxes from exchange to do initial sync. I have 17 mailboxes which won't sync due to the error below: I've ran powershell on the exchange server for 2 accounts as shown below - the one on the left gives me the above error message. The one on the right has synchronised successfully. There is no domain listed which isnt accepted as both accounts have the same domains... Please can anyone help? thanks

Sorry just to clarify: If i set it to 'run whether user is logged on or not' it doesnt run when the server is logged off. If set to 'run when user is logged on' and leave the server logged in, it will run. I'd rather not leave the server logged in and locked from a security aspect. thanks.

Sorry just to clarify: If i set it to 'run whether user is logged on or not' it doesnt run when the server is logged off. If set to 'run when user is logged on' and leave the server logged in, it will run. I'd rather not leave the server logged in and locked from a security aspect. thanks.

Yes that is all correct. Thanks.

I've had a powershell scheduled task running without issues on server 2016 with the option selected 'run whether user logged on or not' The server has been clean installed with server 2019, and imported the scheduled task initially., however I have re-made the task from scratch. Now the issue is that when 'run when only user is logged in' I can right click the task and it runs ok. However,when the server is logged off, the task doesnt run. Can any assist please what may have changed between OS versions? Thanks.

For what reason may I ask?

This isn't a new issue. We've been with psf for years. some Orders are received first time others not to the same recipients ..sometimes received when sent again or last resort manually attach to an email. we got exactly the same response about using another system. To me it's like providing a half working system. Any other platform have no issues sending emails so why Iris!