Alastairb25

Hi All, I require a system that will control access to a separate room within a Sports Centre (this is a part of the School site) Subscription payment, ideally via Wix Provide access via QR or Pin code, ideally via Paxton Net2 Give some kind of analytics for usage Thanks, Alastair

Phil and Carl @Misco

Hi All, Anyone else having issues? We have went through testing and line fine Appears to be Netsweeper related Awful speeds, less than 1mb on downloads from MS, Canva and 365 unusable due to speed. Youtube works sometimes then others shows throughput of 3mb/sec Overall site traffic between 36 and 68mb download and 4-6mb upload, on a 1gb link for a 900 pupil school. Are we alone or are others having same issues? TIA, Alastair

As per subject Nothing on Hub Internal network speeds fine

After Papercut Application Server restart Given a bit of time as interface seems slow to reload (5 minutes) Works Issue seems to have been caused by Papercut Cloud licensing servers going offline earlier today

Update Options Config editor application.modules-enabled type PRINT and update Loads full interface but devices still not talking

Hi All, Cloud licensing issue this morning Back on Papercut MF does not show devices anymore, cannot reinstall to copiers and copiers think they have papercut on but will not work License reinstalled Re synced Server reboot Nothing, anyone in same boat ? TIA, Alastair

Since midnight Bits have come back, but various services do not work, inc Talk straight hub I would assume its related to this, however I cannot check as the hub is down Email of Network works - Monday 22/10 @ 15:19 Event #1169 Network Maintenance - Created - Status: Planned A new event has been opened, Event #1169 Network Maintenance Good Afternoon, We will be performing network maintenance on our ring network where we will be bringing live our other 400Gbps links. There will be no downtime while we are performing this as we are doing one link this evening and the final link tomorrow evening. This will be thoroughly tested to make sure there is no customer impact in the following morning. If we have any concerns then we will be enacting our rollback plan as to ensure customer service is not affected. Regards Technical Department To view the latest update, please visit the Event #1169 Status page. To edit your subscription or unsubscribe, please visit Subscription Management. Best Regards Talk Straight

Was informed that this is way to check for ESU For us planning to do a build, [patch up, confirm reg key then look at a mass redeployment to replace existing builds HKEY_CURRENT_USER\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Windows\ConsumerESU If the ESUEligibility value is anything other than zero, ESU is enabled.

Hi, We are using W10 with ESU (Extended Security Updates) According to Microsoft we need:- W10 22H2 KB5046613 Is anyone in a similar boat? We`ve had issues getting KB5046613 to install. Thanks, Alastair

What filtering is everyone using With it being Cloud based it could be filter related / proper exceptions in place?

This is worrying.. We have a planned upgrade to v2 in Sept half term

Ping works ok Assume filter related Call logged Around 1 hour out as at 9.25am Thanks

A while ago, I think as I recall our Supplier forced a sync with Apple school manage and Jamf, something to do with version release, worked ok in the end

Are you Cisco or HP? We were concerned at high CPU, its not something we have normally looked to know what is "normal" Will likely put back, we just want to see what works and gradually re implement features and monitor

Ok so broad answer so far Storm control 10% - Probably to low, supplier recommended 30% - disabled for moment After around 30 minutes CPU usage on Core for DHCP Snooping and DHCP Snooping HA dropped, from being circa 53% and 23% I suspect on a large network with low usage over summer a variable limit of 10% could be the culprit, as soon as we hit that limit, via devices and DHCP broadcast etc DHCP process fails, but machines keep on requesting, the cycle then repeats due to the storm control limit After a while DHCP Snooping and DHCP Snooping HA went higher again circa 30% and 10% respectively, for the moment we have disabled DHCP snooping, overall total CPU usage of 6%

We did have a planned power outage over the summer, Core shutdown for it. I was already thinking a bouncing the core later today might be an idea

Ours seems more likely to be Cisco related Temporarily removed storm control, set at 10% DHCP snooping turned on with 4 ports used by 2 hosts allowed show process cpu sorted DHCP Snooping taking circa 53% DHCP Snooping HA taking circa 24% Next highest process 0.5% Seems its Cisco related, overall CPU running 86%

Its more like Client has an Offer from DHCP server but fails to send a Request back, then starts on Discover again

We had a similar issue with 2022 once before A working server randomly stopped A wireshark attached from a non working PC

Hi All, We have a spurious issue :- Devices slow to pickup or just fail and get APIPA 169.254.x.x Only recent change is a power outage Cisco configs, and where written Switchports set as access with portfast DHCP on Server 2022, is going up but not giving out anywhere near number of address we would expect Network wide not just one place Giving static IP works fine, but obviously not practical I am building another DHCP Has anyone had issues with Server 2022 DHCP? Have also checked basic things like firewall not come on, can ping etc TIA Alastair

@SIMS_Customer_Support We are a Secondary

As above Have this argument every year as so many systems sync from SIMS it delays everything Surely SIMS can roll now as long as the inset days, today and 2nd and set as such (whatever SIMS terminology is, I am not MIS side of IT) Thanks

Thats the issue, none of ours seem to use SCORM I can extract the video file assuming thats the major part of it

We only have one license for the DSL The idea is they should be only one sending sensitive info The Council also have it and you get a license if they send to you in order to reply back Unsure about that, we have traditionally used it via the Web interface or Outlook addin