ISDN config for a Cisco 803 voice router

[robk]

Can anyone tell me what I need to configure to get a Cisco router with pots ports to make an outgoing call?

 

We have a fault with our ISDN routing, which I need to prove if its our pbx or BT!

 

Not a Cisco Expert....

[john]

Can you pick and pull info from this post maybe? - http://forums.whirlpool.net.au/archive/144720

[robk]

Thanks @john That link gave me another set of configs to try. I have the following at the moment. xxxxxxxxxxx is a blanked out version of the school main phone number...

 

TinyROM version 1.2(2)
16:22 08/02/99
Copyright (c) 1998-1999 by cisco Systems, Inc.
All rights reserved.

POST ......... OK.  12MB DRAM, 12MB Flash.

auto-boot: failed, "no such file"

Booting "c800-k9osy6-mw.123-15a.bin" ...,
             Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

          cisco Systems, Inc.
          170 West Tasman Drive
          San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) C800 Software (C800-K9OSY6-MW), Version 12.3(15a), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Fri 22-Jul-05 00:39 by dchih
Image text-base: 0x00195000, data-base: 0x00F4C000


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
[email protected].

Cisco C803  (MPC850) processor (revision 1) with 56024K bytes of virtual memory.
Processor board ID JAD03368274 (2190931697)
CPU part number 0x2100
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
2 POTS Ports
1 Ethernet/IEEE 802.3 interface(s)
1 ISDN Basic Rate interface(s)
12M bytes of physical memory (DRAM)
8K bytes of non-volatile configuration memory
12M bytes of flash on board (8M from flash card)

no ip route-cache
       ^
% Invalid input detected at '^' marker.

no ip route-cache
       ^
% Invalid input detected at '^' marker.



Press RETURN to get started!


*Mar  1 00:00:50.866: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
00:00:51: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to up
00:00:55: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed state to down
00:00:55: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:2, changed state to down
00:00:56: %SYS-5-CONFIG_I: Configured from memory by console
00:00:56: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C800 Software (C800-K9OSY6-MW), Version 12.3(15a), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Fri 22-Jul-05 00:39 by dchih
00:00:56: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
00:00:58: %LINK-3-UPDOWN: Interface BRI0, changed state to up
Router>
Router>
Router>
Router>enable
Password:
Router#show configuration
Using 1227 out of 8077 bytes
!
version 12.3
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$iz63$UhmbZ0z.DNC8Gl42JswCM.
enable password password
!
!
dial-peer voice 1 pots
no caller-id
no forward-to-unused-port
call-waiting
ring 0
no silent-fax
registered-caller ring 1
port 1
volume 3
destination-pattern xxxxxxxxxxx
!
dial-peer voice 2 pots
no caller-id
no forward-to-unused-port
call-waiting
ring 0
no silent-fax
registered-caller ring 1
port 2
volume 3
!
pots country GB
!
no aaa new-model
ip subnet-zero
no ip routing
!
isdn switch-type basic-net3
!
!
!
!
!
!
interface Ethernet0
ip address 192.168.0.1 255.255.255.0
no ip route-cache
!
interface BRI0
no ip address
encapsulation ppp
no ip route-cache
dialer pool-member 1
isdn switch-type basic-net3
isdn point-to-point-setup
isdn voice-priority xxxxxxxxxxx out always
isdn voice-priority xxxxxxxxxxx in always
isdn incoming-voice modem
ppp authentication chap pap dialin
ppp multilink
!
ip classless
ip http server
no ip http secure-server
!
!
line con 0
stopbits 1
line vty 0 4
password password
login
!
no rcapi server
!
!
end

 

Can anyone spot why this fails? It may be I have a faulty router, or just bad luck!