Jackd Posted December 8, 2008 Posted December 8, 2008 I've got 3 network cards in my debian box, ive got two that are on the same subnet which are 192.168.2.1/255.255.252.0 and 192.168.2.10/255.255.252.0 When i send traffic to 192.168.2.10 it goes through the 192.168.2.1 card, i presume this is some sort of routing issue. How can i fix it so that the traffic for each ip goes through the correct network card for it? Thanks Jack
yabbadabba Posted December 8, 2008 Posted December 8, 2008 Can you set up the Default Gateway on the cards individually?
featured_spectre Posted December 8, 2008 Posted December 8, 2008 You need to put each card on a different subnet or *nix will use one out of the 2. I learnt that the hard way
james_yale Posted December 9, 2008 Posted December 9, 2008 This is actually the correct behavior, the problem is down to the arp replies coming from any interface on the box before you get to ping it. You can change the way it works by setting some options in /etc/sysctl.conf (example from a load balancer, but it's the same principle): #======================================================================== # UltraMonkey requirements below # # Enable configuration of arp_ignore option net.ipv4.conf.all.arp_ignore = 1 # When an arp request is received on eth0, only respond if that address is # configured on eth0. In particular, do not respond if the address is # configured on lo net.ipv4.conf.eth0.arp_ignore = 1 # Ditto for eth1, add for all ARPing interfaces net.ipv4.conf.eth1.arp_ignore = 1 # Enable configuration of arp_announce option net.ipv4.conf.all.arp_announce = 2 # When making an ARP request sent through eth0 Always use an address that # is configured on eth0 as the source address of the ARP request. If this # is not set, and packets are being sent out eth0 for an address that is on # lo, and an arp request is required, then the address on lo will be used. # As the source IP address of arp requests is entered into the ARP cache on # the destination, it has the effect of announcing this address. This is # not desirable in this case as adresses on lo on the real-servers should # be announced only by the linux-director. net.ipv4.conf.eth0.arp_announce = 2 # Ditto for eth1, add for all ARPing interfaces net.ipv4.conf.eth1.arp_announce = 2 # Enables packet forwarding net.ipv4.ip_forward = 1 # # UltraMonkey requirements above #======================================================================== /sbin/sysctl -p will apply the changes.
Teth Posted December 9, 2008 Posted December 9, 2008 Dead right there. arp is ethernet technology while TCP/IP is a layer of abstraction above it. TCP/IP packets get sent down to the Ethernet layer which has no knowledge of the TCP/IP layer. Therefore as far as packets on your hardware network cards are concerned either card is a perfectly acceptable way into the device's TCP/IP stack where they then get routed to the correct address. Loadbalancing is what you need and the linux Kernel is great at and the instructions above should get you going. A machine can never successfully have 2 default gateways. You can specify 2 in Linux but only 1 will work. Default gateway is the default route to send a packet if you don't know the exact destination of that packet so there can be only 1. TCP/IP on LAN networks or internet follows a simple rule. It looks at the IP address, Splits it into Network address and Device address using the subnet mask and then asks itself the question. Do I know where that network is? If its does it send the packet out that interface to its intended recipient. If it doesn't it sends it to its defined default gateway which then makes the same choice. To use TCP/IP to send packets over particular interfaces requires a routing table and the interfaces have to be on different TCP/IP networks. The routing table can be an automatically generated one like the internet or in simpler LAN networks a static routing table manually configured.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now