BentleyMiller86

Hi JRA This is my layout below, it only pins to task bar but your welcome to copy it and modify Thanks

Hi all, Does anyone know why the FMS Equipment Register would not update room names from SIMS? I have a site where classroom have been renamed in SIMS but when the FMS equipment register is loaded, it does not request any updates from SIMS. Can this update be run manually in any way? Thanks

Thanks Guys, I have re punched the face plate downstairs and its now working. I should have more faith in myself

Hi Steve, Yes both faceplates follow the same standard A in this case I think? I will check tomorow that I have punched them correctly, been colour blind I do sometimes muck up my cables! Thanks Rob

Hi All, I haven’t done much structured cabling so I am after some help, I live in a circa 1920’s house which has a solid brick wall construction so Wi-Fi is a major pain in the behind for me at the moment, I have a Netgear Nighthawk AP that I have installed roughly central to our living space, so it should cover all our bedrooms, dining room, living room and kitchen. I have a cable running from my main comm's area to upstairs both cables have a RJ45 face plate on (more info below) I followed the punch pattern on both plates (admittedly knowing this probably wouldn’t work) so I need to know where I have gone wrong, if you could please advise 😊 Cable route is: Switch > RJ45 plate (downstairs) > RJ45 plate (upstairs) > Nighthawk AP Both RJ45 plates are punched as follows Pin 1 – Orange / White 2 – Orange 3 – Green / White 4 – Blue 5 – Blue / White 6 – Green 7 – Brown / White 8 – Brown Cable tester shows my that all pins have successfully crimped, so I have done something wrong with the ordering of them! Thanks 😊 Rob

Hi Chris, These hosts are new, less than a year. I will check for Firmware updates again during the summer holidays but they were all up to date the last time I checked. All Hops are at 1000, I made it my mission to have all 10/100 switching and connections sorted before the summer holidays, the only 100 connections I have now are to printers which still don't have 10/100/1000 NIC's in them, not much I can do about that really. I may lower the resources to see if it makes any difference, but the likelihood of adding more hosts is very slim, Sophos, SIMS are now / going to be cloud based so its more likely I will be turning VM's off. Thanks

Hi Chris, There's nothing in EV to indicate any issues, in terms of Load DC uses 25% of RAM and 0-10% of CPU, MIS uses 50-80% of RAM and 10-20% of CPU so there more then comfortable. All switching is 10/100/1000 HP un-managed Hi XiJ, Yes they are mechanical, unfortunately SSD's are one of the first things to go when savings are needed to be made! however its a standard build I have the same setup in other sites that do not replicate the issues I have at others. Hi Jcx500, The majority of my sites already use more resources than this, It may be possible when SIMS moves to the cloud, but not while its local.

Hi all, I have a few sites that have VM's as their DC and MIS Servers sat on a nice beefy Host, Host's by rule are: 2 x 16 Core Xeon Processors 64GB RAM 4 NIC in 1 Team A few of them offer really poor performance when in the GUI but data transfer rate for network shares, and logon / folder redirection are all running nicely, particularly poor are load times when I restart the VM's , one of my DC's often takes up to 20 Minutes to load and iSCSI Backup data transfer rates, incremental backups are OK but the 2 week full backup often takes more than 48 Hours to complete a 1.2TB Backup, I i usually set resources as follows: DC - 16 Cores and 32GB RAM MIS - 4 Cores and 16GB RAM Leaving 12 Cores and 12GB RAM for the Host. Am I over doing it with the resources? And would it have a bearing on my perfornamce issues above? Thanks

Thanks for your feedback I have no idea what the overall length is, but its not going to be close to 100m, much less. Also the Cisco switch wouldn't be used to boot the signal to the HP switch that sits 2 inches below it I will get my tester out when I next visit site, but it wont be for a few weeks yet. Thanks

Hi all, I have a bit of a head scratcher for you I have an up-link from a HP ProCurve in Cab A to Cab B which links in to a Cisco 2960 switch which then links in to another HP ProCurve switch, all the Cisco is doing is bridging the 2 switch's and bringing the entire network down to 100Mb while its sat there doing sweet naff all else, however if I link the Cab A up-link patch directly in to the ProCurve bypassing the Cisco (and going ProCurve to ProCurve), I have no connectivity at all and have to link the Cisco back in to the loop, I really cant understand why? I'm sure the HP's are auto sensing so cabling shouldn't be an issue? has anyone got any ideas? Thanks Rob

Unfortunately not, we have restarted during the day quite a few times to see the data retained, the data is only lost overnight, but there is nothing special set to run overnight. Thanks!

Sorry for the delayed response, been swamped this past week! Everything is local to the Library machine, which is cabled to the network, the only thing that isn't local is the backup, that writes to a shared folder on the DC. Also, there's nothing recent in the recycle bin, its all from Sept 2018 when the Y6 leavers were removed. Looks like ill try re installing the whole thing in the morning, restore the backup and hope it works, it dosn't make any sense, its like the data is just disappearing in to thin air over night. Thanks!

Ha! That's the answer I don't want Staff member has data on she want's wouldn't be that bothered if I didn't know the code... but i do!!! Thanks

Unfortunately no, I only get the Update & Restore option, plugging in to a PC or Mac only works if you have a backup of the iPad available, which I don't. Thanks

Hi all, Pretty sure I know the answer to this one, even if it's not the one I want to hear! A Teacher left her iPad in an accessible place, the iPad was passcoded and was picked up by an eager student, basically its now in an iPad is Disabled state with no countdown for a re try after the student spend some time trying code after code, but I know what the code is!!! Is there anyway of unlocking the thing? It isn't managed with any MDM so it cant be unlocked via Profile Manager or anything, or is it a case of full restore? I have tried the Backup and Restore trick but have had no luck with that, not sure its even an option anymore on iOS 12? Thanks