nLinked

This opportunity has now been extended. An exciting opportunity exists for an ICT Technician to join our successful ICT Support Team, housed in a state-of-the-art school, under new leadership. This post would be ideally suited to someone reliable and hardworking and who has a real interest in all aspects of Information and Communication Technology and wishes to develop their skills. This position will be first line technical support and maintenance for hardware and software on the school’s network, including wireless. The starting salary is dependent on qualifications and relevant experience. Please see attachments for full details. ICT Technician JD 2014.docx ICT Tech Advert Sept 14.docx

To be responsible for managing and maintaining the Media suite and assist in the administration of VLE/website content. 35 hours per week, Term Time only plus 2 Inset days. 8.30am – 4.30 pm Mon-Friday. Full details on our website here.

To be responsible, through the ICT support team, for the care and maintenance of ICT equipment and materials throughout the school. 35 hours per week, Full Time. Full details on our website here.

That did it! I remember now we were testing another device via a small unmanaged switch, but this was plugged into the HP not the Cisco. Anyhow, unplugging that switch resolved communication from the Cisco switch. It must have been going through this little unmanaged switch, getting lost. Thanks!

We have a Cisco 6513 connected to a HP 5412 switch. Port GigabitEthernet1/25 on the Cisco has the following settings: no ip address switchport switchport access vlan 100 switchport mode access spanning-tree portfast spanning-tree bpduguard enable A device plugged into that port was able to communicate to devices on vlan 100 just fine for the last few months. But just after rebooting the Cisco switch recently, any device connected to that port no-longer can communicate. We have made no changes to its config, and the running config before the reboot was saved. What could have made it lose connectivity with vlan 100 just by rebooting? Thanks.

Thank you!

Sometimes SIMS .net usage becomes very high, with CPU spikes on the server. This normally happens when a user is running a large report. It then sometimes (rarely) causes SIMS .net to slow down or crash for other users. Is there any way to check, in these occasions, which user is running a large report in realtime? Thanks.

Thanks, I've attached the startup-config. The VLAN we're having trouble with is 104. Any suggestions most appreciated.core2-b-block-startup-confg - Copy.txt

One of our vlan's (ID: 104) stopped working suddenly and computers on that vlan failed when trying to obtain a dhcp ip address. On the Cisco switch if we do show vlan, this command is supposed to shows the vlans in the vlan.dat file. We notice it has every other vlan except the one that is now missing. If we show the running-config or even the startup config, they DO show the missing vlan (as if everything is fine), but that vlan doesn't take effect. We tried deleting the "missing" vlan using clear vlan 104, but it says No subinterface configured for vLAN Identifier 104, so it's already missing. Recreating the vlan, saving and rebooting still doesn't add it into the vlan.dat or make the vlan work. The switch is in vtp server mode. Any ideas appreciated.

5 years later, is there now an official silent way to deploy FMS updates?

Quick update, Capita saw the file and said it's corrupt but they can't give a reason. They managed to recover it though.

I've managed to restore a previous version of the SPL file to last week from our backups, and it opens fine, so at least I don't have to redo that work. But the strangest thing is, I was working on later versions of that file since yesterday and it was opening fine! Now that later version doesn't, nor any of the versions I restore from our backups from a few days before! And yet the latest versions are also larger in size so they really should have data in them.

Thanks, case logged, will update.

My Nova version seems OK, it's the same computer and it opens the file. I have the SPL file saved to my documents and it has always opened fine before. Just when I came to open it last the timetable is all gone! I'm sure I'm pointing it to the correct directory too, it's just an SPL file in my documents which I've always opened well before.

Have been working on a timetable in Nova T6 for a few days. It was saving everything fine since. But when I now open it, the timetable is gone, it's all blank. I can see some data like staff lists, but no table. I've even tried opening the backup files it automatically creates every half hour and they're also all blank. I've tried another computer too. What could it be?! I think it's lost everything I've worked on!