Dos_Box Posted August 30, 2007 Posted August 30, 2007 I have a wonderful HP 2800dtn here, but tit has today refused to recognise 3 new colour carts we have put in. The display and webmin shows then as being low\empty. These are new HP carts and not refills. I have some printers which you have to tell it that new carts have been inserted but cannot find anything on the 2800. Any help?
contink Posted August 30, 2007 Posted August 30, 2007 Obvious possibles that you will doubtless have tried.. - Power off and then on (IT crowd anyone?) - Try powering off, removing cartridges, waiting for printer to complain and then installing one, seeing if it accepts it (power cycle again if not) repeat Beyond that can't think of anything obvious...
kearton Posted August 30, 2007 Posted August 30, 2007 We had the same sorts of problems here with 2 HP inkjets. Not sure of the model off the top of my head. They were A3 ones tho. Apparently if you took the cartridges out when it was switched on it buggered up something. Basically we had to ship it back for repair... Could this have happened?
Dos_Box Posted August 30, 2007 Author Posted August 30, 2007 Obvious possibles that you will doubtless have tried.. - Power off and then on (IT crowd anyone?) - Try powering off, removing cartridges, waiting for printer to complain and then installing one, seeing if it accepts it (power cycle again if not) repeat Beyond that can't think of anything obvious... Nope. Thats' not worked. It may be borked.
contink Posted August 30, 2007 Posted August 30, 2007 Nope. Thats' not worked. It may be borked. Bugger... Sounds like a call to HP tech support is in order.. it does sound a lot like kearton's suggestion may be at the heart of it though @Kearton: Love the sig
Geoff Posted August 30, 2007 Posted August 30, 2007 Also make sure the little copper contacts are clean on both the printer and the cartridge. Otherwise the chip on the cartridge wont be able to talk to the printer.
Ric_ Posted August 30, 2007 Posted August 30, 2007 I had this problem on a BusinessInkjet 1100... basically, some heavy handed luser had managed to snap the plastic switch underneath the cartridge which detects how much ink is left by pushing on the 'bag' in the cartridge.
Dos_Box Posted August 30, 2007 Author Posted August 30, 2007 It is the chips on the carts which have 'blown' due to being inserted whilst switched on. New carts register fine. Phew.
kearton Posted August 30, 2007 Posted August 30, 2007 OK, to clarify my previous email (i.e I've spoken to someone else here who knew the whole story)... We had problems with the 2600 model inkjets. We put in new carts and it said they were low/empty. We spoke to the HP reseller and they said that if you replaced the carts without turning the power off it could fry something. We had to send two back for repair. So it sounds like a very similar prob, Dos_Box
Dos_Box Posted August 30, 2007 Author Posted August 30, 2007 Yup. Under the cartridge cover is a diagram showing that the power must be OFF before removing and inserting new ink. Bugger.
contink Posted August 30, 2007 Posted August 30, 2007 Yup. Under the cartridge cover is a diagram showing that the power must be OFF before removing and inserting new ink. Bugger. Expensive lesson but at least not as expensive as a new printer.
john Posted August 31, 2007 Posted August 31, 2007 What a PITA this is! I always swap on the fly its very rare I turn anything off when changing inks and toners. May have to start remembering to turn them off.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now