Cisco 877w Routing issue

[TheChunk]

Hi Guys,

 

I'm having trouble with the initial setup of a Cisco 877w - I've managed to setup the connection externally with no issues, the router itself can PING hostnames and IP addresses externally but internal hosts won't route out and I just can't see why. ANY help is much appreciated.

 

Config has been configured solely through CLI and is as follows (i've omitted the crypto key and usernames/passwords for obvious reasons):

 

Current configuration : 3551 bytes

!

version 12.4

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname

!

boot-start-marker

boot-end-marker

!

no logging message-counter syslog

enable secret 5

!

no aaa new-model

!

!

dot11 syslog

!

dot11 ssid

vlan 1

authentication open

authentication key-management wpa

guest-mode

wpa-psk ascii 7

!

ip cef

!

!

no ip dhcp use vrf connected

ip dhcp excluded-address 192.168.50.1 192.168.50.100

!

ip dhcp pool LOCAL_POOL

network 192.168.50.0 255.255.255.0

dns-server 8.8.8.8 8.8.4.4

default-router 192.168.50.1

!

!

ip domain name

!

multilink bundle-name authenticated

!

!

!

!

archive

log config

hidekeys

!

!

!

bridge irb

!

!

interface ATM0

no ip address

shutdown

no atm ilmi-keepalive

dsl operating-mode auto

!

interface FastEthernet0

!

interface FastEthernet1

!

interface FastEthernet2

!

interface FastEthernet3

description WLAN_Interface

switchport access vlan 10

!

interface Dot11Radio0

no ip address

!

encryption vlan 1 mode ciphers aes-ccm

!

ssid

!

speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0

station-role root

!

interface Dot11Radio0.1

encapsulation dot1Q 1 native

ip virtual-reassembly

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface Vlan1

no ip address

ip virtual-reassembly

bridge-group 1

!

interface Vlan10

description WAN Interface

no ip address

no ip redirects

no ip unreachables

no ip proxy-arp

ip virtual-reassembly

pppoe enable group global

pppoe-client dial-pool-number 1

!

interface Dialer1

ip address negotiated

ip access-group ACL-OUTSIDE-IN in

ip access-group ACL-INSIDE-OUT out

ip mtu 1492

ip nat outside

ip virtual-reassembly

encapsulation ppp

dialer pool 1

ppp authentication chap pap callin

ppp chap hostname

ppp chap password 7

ppp pap sent-username password 7

!

interface BVI1

ip address 192.168.50.1 255.255.255.0

ip nat inside

ip virtual-reassembly

!

ip forward-protocol nd

ip route 0.0.0.0 0.0.0.0 Dialer1

!

!

no ip http server

no ip http secure-server

ip nat source list INSIDE_NETWORK interface Dialer1 overload

!

ip access-list standard INSIDE_NETWORK

permit 192.168.50.0 0.0.0.255

!

ip access-list extended ACL-INSIDE-OUT

permit ip any any

ip access-list extended ACL-OUTSIDE-IN

deny ip any any log

!

!

!

!

!

control-plane

!

bridge 1 protocol ieee

bridge 1 route ip

banner motd ^CC

Unauthorized access to this device is prohibited!

^C

!

line con 0

password 7

logging synchronous

no modem enable

line aux 0

line vty 0 4

password 7

logging synchronous

login

transport input ssh

!

scheduler max-task-time 5000

end

[TheChunk]

And the "show ip interface brief":

 

Interface IP-Address OK? Method Status Protocol

ATM0 unassigned YES NVRAM administratively down down

BVI1 192.168.50.1 YES NVRAM up up

Dialer1 192.168.56.42 YES IPCP up up

Dot11Radio0 unassigned YES NVRAM up up

Dot11Radio0.1 unassigned YES unset up up

FastEthernet0 unassigned YES unset up down

FastEthernet1 unassigned YES unset up down

FastEthernet2 unassigned YES unset up down

FastEthernet3 unassigned YES unset up up

NVI0 unassigned YES unset administratively down down

Virtual-Access1 unassigned YES unset up up

Vlan1 unassigned YES NVRAM up down

Vlan10 unassigned YES NVRAM up up