+ Post New Thread
Results 1 to 8 of 8
AV and Multimedia Related Thread, SANYO PLC-XU70 POWER BLINKING RED THEN SHUTS DOWN in Technical; Hello everybody, i just registered on this website and i can see there are many professional experts and i hope ...
  1. #1

    Join Date
    Sep 2013
    Posts
    7
    Thank Post
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0

    SANYO PLC-XU70 POWER BLINKING RED THEN SHUTS DOWN

    Hello everybody, i just registered on this website and i can see there are many professional experts and i hope soemoen can give me some help!
    I have a projector sanyo plc-xu70, was working fine until last week, now it won't turn on anymore.When i press the power button, the power led starts green then after few seconds it starts blinking red and then it just shut down the projector.
    On the manual it seems that is a problme of the tempearature inside, but how can it be if the projector is really cool down?
    I read on another post that it might be the thermal switch to turn off, but where is it? If i open the case, where can i find it?
    Thank you in advance!

  2. #2
    robriley's Avatar
    Join Date
    Aug 2008
    Location
    Leicestershire
    Posts
    35
    Thank Post
    17
    Thanked 3 Times in 3 Posts
    Rep Power
    13
    From what you have said the way it turns off... I would suspect the lamp might need replacing. Might be worth taking it out and seeing if its gone pop.

  3. #3

    Join Date
    Sep 2013
    Posts
    7
    Thank Post
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    But the lamp replace led doesnt even turn on and the lamp until few days ago was working fine, very bright, i think something by mistake send the signal that the projector is too hot and it automatically shuts down but how can i fix it?

  4. #4

    plexer's Avatar
    Join Date
    Dec 2005
    Location
    Norfolk
    Posts
    13,615
    Thank Post
    747
    Thanked 1,707 Times in 1,520 Posts
    Rep Power
    437
    Search Edugeek for sanyo you will find posts relating to the thermal trip on the xe40 I think it is that may help you.

    Ben

  5. #5

    Join Date
    Sep 2013
    Posts
    7
    Thank Post
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    I looked at that post about the xe40, it shows like a button to press to reset the thermal switch, but i opened the case and i took the fan off and i clicked on that switch by side, nothing changes.I think is soemthing else, any ideas please?

  6. #6

    Join Date
    Sep 2013
    Location
    Scotland
    Posts
    1
    Thank Post
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Did you push down on the trip switch until you felt a very light click? This switch having tripped is almost always the problem for this symptom. Sometimes it trips because the lamp is faulty but very often it's due to a build up of dust, clean the fans and filters and try again. Good luck!

  7. #7

    Join Date
    Sep 2013
    Posts
    7
    Thank Post
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Yes i did, i clicked on that switch, still the same...what else can i check?

  8. #8
    TechSupp's Avatar
    Join Date
    Mar 2007
    Location
    South Yorkshire
    Posts
    1,972
    Thank Post
    320
    Thanked 126 Times in 106 Posts
    Rep Power
    42
    Had a similar thing, tried all sorts, in end returned under warranty, turned out to be a faulty bulb.



SHARE:
+ Post New Thread

Similar Threads

  1. Sanyo PLC-XE40 power up problem
    By bertster in forum AV and Multimedia Related
    Replies: 6
    Last Post: 11th April 2014, 10:32 AM
  2. Sanyo PLC-XU70 projectors going faint
    By Zourous in forum Hardware
    Replies: 0
    Last Post: 21st March 2013, 01:25 PM
  3. Sanyo Plc-xu105 powers on then goes to stand by
    By Klim0k in forum AV and Multimedia Related
    Replies: 7
    Last Post: 7th September 2012, 05:02 PM
  4. Sanyo PLC-XW57 power on then goes into standby
    By LOUD in forum AV and Multimedia Related
    Replies: 14
    Last Post: 1st May 2012, 11:21 PM
  5. Sanyo PLC-XW57 Power Down
    By pfaulkner in forum AV and Multimedia Related
    Replies: 6
    Last Post: 29th September 2011, 11:43 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •