+ Post New Thread
Results 1 to 6 of 6
Wireless Networks Thread, HP ProCurve Switch Dropping FTP (Active) and IPSec traffic in Technical; Hello Everyone, I've set up a ProCurve 1810 to sit inbertween my internet connection any my internal networks gateway. I've ...
  1. #1
    fawkers's Avatar
    Join Date
    Jun 2007
    Location
    Southend
    Posts
    193
    Thank Post
    32
    Thanked 22 Times in 21 Posts
    Blog Entries
    2
    Rep Power
    30

    HP ProCurve Switch Dropping FTP (Active) and IPSec traffic

    Hello Everyone,

    I've set up a ProCurve 1810 to sit inbertween my internet connection any my internal networks gateway. I've assigned ports 1 - 4 to be part of a VLAN and attached our internet router and our gateway to two of these ports. This is in preperation for a new gateway that is going in.

    However when in this configuration Active FTP (not pasive) and IPSec traffic seams to get blocked\dropped. Plug the internet straight back into our gateway and all returns to normal.

    anyone ever seen this before?
    Last edited by fawkers; 16th May 2011 at 03:05 PM. Reason: typo

  2. #2

    Join Date
    Oct 2007
    Posts
    131
    Thank Post
    16
    Thanked 14 Times in 14 Posts
    Rep Power
    16
    have you patched the firm ware on these the is a known issue on all but the latest firmware, they stop responding on the HTTP interface and hang, I found info on the procurve forums and the firmware is on the mini site HP Networking: switches, routers, wired, wireless, HP TippingPoint Security think version 1.7 is the latest!

  3. #3

    m25man's Avatar
    Join Date
    Oct 2005
    Location
    Romford, Essex
    Posts
    1,608
    Thank Post
    49
    Thanked 444 Times in 330 Posts
    Rep Power
    136
    What devices are we talking about here? and what are you trying to acheive?

    Your ISP's Router and your Schools Gateway Appliance? or the LEA managed switch and a router?

    If they are configured as a transparent bridge the Switches MAC will mess things up or if the switch is a Gigabit Switch try locking the port speeds down.
    Which device holds your Public IP address?

  4. #4
    fawkers's Avatar
    Join Date
    Jun 2007
    Location
    Southend
    Posts
    193
    Thank Post
    32
    Thanked 22 Times in 21 Posts
    Blog Entries
    2
    Rep Power
    30
    We have 2 new gateway devices which act in a cluster, so both need to be connected to our internet gateway Cisco (direct connection to BT, no LA filtering etc). I need to test and conf. these devices before we go live with them so the swich has to split the incomming connection 3 ways, 1 to the existing gateway and 2 to the new gateways. We have a /28 for our public IP's so each device is on a different public IP.

    The Switch in question is a HP ProCurve 1810G-24 J9450A using the most upto date firmware which i beleave is 2.2

    oh yes and speeds have been locked down on the ports to 100Full
    Last edited by fawkers; 16th May 2011 at 03:48 PM.

  5. #5

    Join Date
    Jun 2011
    Location
    Miami
    Posts
    2
    Thank Post
    0
    Thanked 1 Time in 1 Post
    Rep Power
    0
    Did you find any solution ? We have the same problem !

    Thanks !

  6. #6

    Join Date
    Jun 2011
    Location
    Miami
    Posts
    2
    Thank Post
    0
    Thanked 1 Time in 1 Post
    Rep Power
    0
    a.. and its the 2.2 firmware !

  7. Thanks to igerlster from:

    fawkers (15th August 2011)

SHARE:
+ Post New Thread

Similar Threads

  1. problem with ISCSI Traffic dropping
    By sacrej in forum Hardware
    Replies: 11
    Last Post: 2nd March 2011, 11:45 AM
  2. [Wanted] HP ProCurve Switch GL 20 PortModule Switch (J4908A)
    By robknowles in forum Classified Adverts
    Replies: 4
    Last Post: 6th November 2009, 08:14 PM
  3. Replies: 0
    Last Post: 6th November 2009, 08:10 PM
  4. PDC traffic crashes switch?
    By morganw in forum Hardware
    Replies: 9
    Last Post: 27th August 2009, 10:14 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •