+ Post New Thread
Results 1 to 5 of 5
Wireless Networks Thread, Extricom - Documents?! in Technical; Hey guys, I've just been trying to connect to the Extricom switch (EXSW 1200) through the console port. Does anyone ...
  1. #1

    Join Date
    May 2008
    Location
    Cheshire
    Posts
    270
    Thank Post
    47
    Thanked 27 Times in 24 Posts
    Rep Power
    18

    Extricom - Documents?!

    Hey guys, I've just been trying to connect to the Extricom switch (EXSW 1200) through the console port. Does anyone have any documents for the switch with the correct settings?

    Thanks,

  2. #2

    bossman's Avatar
    Join Date
    Nov 2005
    Location
    England
    Posts
    3,853
    Thank Post
    1,160
    Thanked 1,028 Times in 729 Posts
    Rep Power
    323
    @Pashers:

    Would this be of any help?
    Allied Telesis, Inc :: EXSW-1200

  3. #3
    MicrodigitUK's Avatar
    Join Date
    May 2007
    Location
    Wiltshire
    Posts
    309
    Thank Post
    33
    Thanked 51 Times in 47 Posts
    Rep Power
    23
    If your after the Hyper Terminal setings I think they are ath same as Cisco ones.
    Bits per sec : 9600
    Data bits : 8
    Parity : none
    Stop bits : 1
    Flow control : none

    and just use a standerd null modem cable for console conection to pc.

  4. #4
    keeleyp's Avatar
    Join Date
    Dec 2008
    Location
    Fleet
    Posts
    2
    Thank Post
    0
    Thanked 1 Time in 1 Post
    Rep Power
    0

    Exsw 1200 Connection Settings

    There is little point connecting to the console as all configuration is done via the web interface.

    If you do not know the IP address of the switch then the console will tell you,

    Connection speed is
    115200 bps
    8 data bits
    No parity
    1 Stop bit
    No Flow Control

    if the passwords are at default the you will need to login as operator with a password of 12345

    this should allow you to issue the ifconfig command, which will tell you the IP address of the switch which you can then access over https:// to configure the switch.

    the ifconfig command shows several interfaces, only one should have an IP address, dependant on the firmware revision, older versions had the address against interface ipx0 newer releases address via interface br0.

    Note: the 1200 has 2 ethernet interfaces, only the left hand one is used.

    Hope this helps

  5. Thanks to keeleyp from:

    Pashers (10th August 2009)

  6. #5

    Join Date
    May 2008
    Location
    Cheshire
    Posts
    270
    Thank Post
    47
    Thanked 27 Times in 24 Posts
    Rep Power
    18
    Hey guys, after much of a headache, I've managed to find the IP address of the switch and connected to it using the Console. Now I'm back on using the web interface!

    Thanks again for all your help!

SHARE:
+ Post New Thread

Similar Threads

  1. Extricom wireless solution
    By markcuk in forum Hardware
    Replies: 67
    Last Post: 20th January 2010, 03:53 AM
  2. Issues with Extricom EXRP - 40 and intel 3945ABG?
    By Tony_Mc in forum Wireless Networks
    Replies: 29
    Last Post: 2nd October 2009, 02:13 PM
  3. Extricom Switch
    By Pashers in forum Learning Network Manager
    Replies: 7
    Last Post: 13th May 2009, 12:06 PM
  4. Ruckus/Extricom Wireless
    By markesmith in forum Wireless Networks
    Replies: 3
    Last Post: 6th October 2008, 11:10 AM
  5. Replies: 4
    Last Post: 26th June 2008, 01:54 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •