+ Post New Thread
Results 1 to 3 of 3
Wired Networks Thread, Problem with switch SG500 of cisco in Technical; We are using switch of Cisco belong to series SG500. The current, we saw some of the problems after use ...
  1. #1

    Join Date
    Dec 2013
    Posts
    1
    Thank Post
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0

    Problem with switch SG500 of cisco

    We are using switch of Cisco belong to series SG500. The current, we saw some of the problems after use the switch (detail below). Please support for us.

    Here is a desciption of the problem
    -When the switch is started, it runs very normally. The devices are connected to the switch, the switch will learn the MAC address. The number of MAC address learned on the switch about 2000 MAC.
    -After switch operate about 2-3 weeks, we found that the number of MAC address learned on the switch reduced more than 80 percent, from 2000 MAC to around 300 MAC. The devices are being connected on the switch still operate normally. However, when we move the network cable of device is using from one port on a switch to another port, we were experiencing long delays in reconnecting to the network. The delays are about 10 minutes.

    Detail test after switch operate about 2-3 weeks:
    - First device configured with a static IP of 192.168.1.2 is plugged into port 2 of a cisco SG500 switch.
    - Second device is configured with a static IP of 192.168.1.3 and is plugged into port 3 of the switch.
    - On both device, We start a ping <IP of other PC> -t
    - Then we moves the network cable from port 3 to port 4 of the switch. As soon as we moves the cable, pings on both device stop working, check the switch is not learned MAC of second device. After about 10 minutes, the pings start working again. But the switch is still not learned MAC of second device.

    Here is detailed information of switch that we are using:
    SG500-28 28-Port Gigabit Stackable Managed Switch
    - PID VID: SG5000-28-k9 V02
    - Firmware Version (Active Image): 1.3.0.62
    - Stack unit mode: Standalone
    - System Operational Mode: L2 Mode
    - Jumbo Frames: Enabled
    - Spanning tree protocol: MSTP
    - SMNP : Enabled
    - Port security : Disable
    - Qos: Disable
    - Access control : Disable
    - DHCP : Disable

    Looking forward hearing from you soon.

  2. #2

    Dos_Box's Avatar
    Join Date
    Jun 2005
    Location
    Preston, Lancashire
    Posts
    10,465
    Thank Post
    606
    Thanked 2,190 Times in 1,005 Posts
    Blog Entries
    23
    Rep Power
    633
    Moving to Wired Networks forum.

  3. #3
    Duke5A's Avatar
    Join Date
    Jul 2010
    Posts
    806
    Thank Post
    83
    Thanked 132 Times in 115 Posts
    Blog Entries
    8
    Rep Power
    32
    What kind of devices are plugged into the switch? Reason I ask is because if you don't have a need for jumbo frames to be enabled then I would disable it - it'll cause problems if some of the devices you're plugging into it don't support it, but others do. Also enable portfast on those ports if they aren't already, but only if the devices you're plugging in are clients and not other switches.

SHARE:
+ Post New Thread

Similar Threads

  1. VLAN problem with Cisco SG200-50 switch
    By waldronm2000 in forum Wired Networks
    Replies: 11
    Last Post: 31st August 2012, 12:03 PM
  2. Odd Problem with switch dropping connection
    By phreak in forum Wired Networks
    Replies: 26
    Last Post: 18th June 2012, 12:07 PM
  3. Problems with GPO Install of Adobe Premiere Elements 4.0
    By Ric_ in forum Educational Software
    Replies: 6
    Last Post: 7th November 2011, 02:51 PM
  4. Problem with Cisco Switch
    By Little-Miss in forum Learning Network Manager
    Replies: 12
    Last Post: 8th January 2009, 01:46 PM
  5. Problem with copy of website
    By richard in forum Web Development
    Replies: 6
    Last Post: 6th February 2006, 12:06 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •