+ Post New Thread
Results 1 to 11 of 11
Wired Networks Thread, Cisco - Interface down in Technical; Hi, On a Cisco PIX firewall when running sh int and all ports report back as "Interface Ethernetx "", is ...
  1. #1

    FN-GM's Avatar
    Join Date
    Jun 2007
    Location
    UK
    Posts
    16,315
    Thank Post
    901
    Thanked 1,798 Times in 1,549 Posts
    Blog Entries
    12
    Rep Power
    466

    Cisco - Interface down

    Hi,

    On a Cisco PIX firewall when running sh int and all ports report back as "Interface Ethernetx "", is down, line protocol is down" - Is it safe to assume the device isnt being used?

    Thanks

  2. #2

    twin--turbo's Avatar
    Join Date
    Jun 2012
    Location
    Carlisle
    Posts
    2,334
    Thank Post
    1
    Thanked 381 Times in 340 Posts
    Rep Power
    150
    It means the Ethernets are not in use presently as long as it's not part of some failover then I guess that yes it's probably safe to remove.

    Which PIX is it?

    Rob

  3. #3

    FN-GM's Avatar
    Join Date
    Jun 2007
    Location
    UK
    Posts
    16,315
    Thank Post
    901
    Thanked 1,798 Times in 1,549 Posts
    Blog Entries
    12
    Rep Power
    466
    Off top of my head i am not sure, will check in the morning. Thanks

  4. #4
    cpjitservices's Avatar
    Join Date
    Jul 2010
    Location
    Hessle
    Posts
    2,561
    Thank Post
    530
    Thanked 295 Times in 271 Posts
    Rep Power
    84
    I would say its not being used, however I'd check it physically make sure there's actually nothing plugged into it. Sounds like A PIX 515e.

  5. #5

    SYNACK's Avatar
    Join Date
    Oct 2007
    Posts
    11,270
    Thank Post
    884
    Thanked 2,747 Times in 2,321 Posts
    Blog Entries
    11
    Rep Power
    785
    Yeap, down, down heans that the hardware and software interfaces are down so as above unless it is some fancy failover you should be good.

  6. #6

    twin--turbo's Avatar
    Join Date
    Jun 2012
    Location
    Carlisle
    Posts
    2,334
    Thank Post
    1
    Thanked 381 Times in 340 Posts
    Rep Power
    150
    Got a 525 sitting in my dining room , not in service mind...

    Rob

  7. #7

    FN-GM's Avatar
    Join Date
    Jun 2007
    Location
    UK
    Posts
    16,315
    Thank Post
    901
    Thanked 1,798 Times in 1,549 Posts
    Blog Entries
    12
    Rep Power
    466
    Quote Originally Posted by twin--turbo View Post
    Got a 525 sitting in my dining room , not in service mind...

    Rob
    These are 525

    There is failover there are 2 plugged in. I pulled this config from the one that has all the lights light up on the network ports

  8. #8

    twin--turbo's Avatar
    Join Date
    Jun 2012
    Location
    Carlisle
    Posts
    2,334
    Thank Post
    1
    Thanked 381 Times in 340 Posts
    Rep Power
    150
    is there a cable connecting the 2 a DB25 if so the one that is down is waiting in failover mode.

    Rob

  9. #9

    FN-GM's Avatar
    Join Date
    Jun 2007
    Location
    UK
    Posts
    16,315
    Thank Post
    901
    Thanked 1,798 Times in 1,549 Posts
    Blog Entries
    12
    Rep Power
    466
    There is a cable. Look on the other firewall and the ports are "Interface Ethernetx "", is down, line protocol is down" like the other

  10. #10

    twin--turbo's Avatar
    Join Date
    Jun 2012
    Location
    Carlisle
    Posts
    2,334
    Thank Post
    1
    Thanked 381 Times in 340 Posts
    Rep Power
    150
    Sounds like it's fully defunct then.

  11. #11

    FN-GM's Avatar
    Join Date
    Jun 2007
    Location
    UK
    Posts
    16,315
    Thank Post
    901
    Thanked 1,798 Times in 1,549 Posts
    Blog Entries
    12
    Rep Power
    466
    Quote Originally Posted by twin--turbo View Post
    Sounds like it's fully defunct then.
    Thanks



SHARE:
+ Post New Thread

Similar Threads

  1. cisco ipsec VPN force ALL traffic down tunnel
    By RabbieBurns in forum Wired Networks
    Replies: 10
    Last Post: 7th June 2012, 11:49 PM
  2. cisco catalyst 2924 web interface?
    By FN-GM in forum Wireless Networks
    Replies: 7
    Last Post: 21st September 2008, 03:58 PM
  3. Cisco interface card?
    By j17sparky in forum Wireless Networks
    Replies: 2
    Last Post: 11th March 2008, 01:20 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •