+ Post New Thread
Results 1 to 7 of 7
Network and Classroom Management Thread, network connection!? in Technical; We have windows server 2003 network! The server and main ICT room is in Block (building A) and there are ...
  1. #1

    Join Date
    Jun 2007
    Posts
    5
    Thank Post
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0

    Question network connection!?

    We have windows server 2003 network!
    The server and main ICT room is in Block (building A) and there are about 10 computers connected to the network in the other block (building B). The connection from block A to block B is through Fibre optic cable. We use media converters on either side to convert from and to Ethernet connection!. Now the problem is block B is loosing connection and not connected most times. Any solution please!! And how to check the media converters!!!

    Media converter: Planet fast Ethernet converter 100base tx to 100 base fx

    Thanks in advance!

  2. #2

    FN-GM's Avatar
    Join Date
    Jun 2007
    Location
    UK
    Posts
    15,948
    Thank Post
    886
    Thanked 1,697 Times in 1,475 Posts
    Blog Entries
    12
    Rep Power
    447
    Do you have any fibre patch cables handy? If you do you could try one of them with the media converters and see if the connection drops then. Obviously this will have to be done in the holidays or something.

    Z

  3. #3
    enjay's Avatar
    Join Date
    Apr 2007
    Location
    Reading, Berkshire, UK
    Posts
    4,488
    Thank Post
    282
    Thanked 196 Times in 167 Posts
    Rep Power
    75
    Duff converter is the first place I'd start looking. Do you have a Block C which is also on fibre? If so, try switching the converters over and see what happens. Alternatively, can you get your supplier to lend you one for a few days or negotiate that you buy it now but they take it back if it doesn't help?

  4. #4

    SYNACK's Avatar
    Join Date
    Oct 2007
    Posts
    11,170
    Thank Post
    868
    Thanked 2,697 Times in 2,287 Posts
    Blog Entries
    11
    Rep Power
    772
    This is an easy one if you have even remotely smart switches on either end. Somewhere in any managed or semi managed switch configuration website there should be a port statistics option. This should list any transmit and receive errors on each port. If the error rate is much greater than zero then it is almost definitively a screwy fiber transceiver. In my experience they only have a usable life of about three years.

    I would not connect the transceivers directly with a patch cable unless it is more than 10m long as this has the potential to damage the receiving diode by overloading.

  5. #5
    Hedghog's Avatar
    Join Date
    Jul 2006
    Location
    North Wales
    Posts
    194
    Thank Post
    35
    Thanked 17 Times in 16 Posts
    Rep Power
    37

    Wink

    hi,

    Another thought - I used to have a lot of problems with fiber transceivers when we had a power blip or the IT teachers lost it Wink and used the room power key to switch all the PCs off, the surge when it was switched back on tended to take the fiber link out.
    Cured it with a small UPS for the switch rack.
    Peter

  6. #6

    m25man's Avatar
    Join Date
    Oct 2005
    Location
    Romford, Essex
    Posts
    1,625
    Thank Post
    49
    Thanked 460 Times in 336 Posts
    Rep Power
    140
    How far apart are the transceivers?

    Just because it's fibre does not make it a guaranteed service.

    200 Meters or 500 Meters dependent on cable/transciever types is about all you will get from a standard setup.

    If your cable has any joints in it this will be reduced considerably.

    If your cable has any damage, tight turns or wind exposure the link can be badly affected.

    Without the equipment to test the cable for losses your only hope is to test and confirm that the transcievers actually work.

    Like lightbulbs the lasers used in these devices can go out or reduced output.
    Connecting them to a switch with a short patch cable may be enough to make them indicate a link is up but plug them back into a lossy 130Mtr fibre and it could all be over again very quickly.

    Trust me I know, I have one site with 320 fibre joints and more rats that the houses of parliment. Much of which is 10GBe, You can't leave the office without a TDR strapped to your utility belt!

  7. #7

    mattx's Avatar
    Join Date
    Jan 2007
    Posts
    9,240
    Thank Post
    1,058
    Thanked 1,068 Times in 625 Posts
    Rep Power
    740
    Sounds crazy, but in my old job to test a fibre between buildings - I just used to shine a torch down it, then take a trip to the other end..... [ if I was on my own ]

SHARE:
+ Post New Thread

Similar Threads

  1. Student laptop connection to network
    By RoyG in forum School ICT Policies
    Replies: 35
    Last Post: 4th November 2009, 08:23 AM
  2. Strange network connection problem
    By trekmad in forum Wireless Networks
    Replies: 7
    Last Post: 5th October 2007, 08:04 PM
  3. Network Connection Drops out Randomly
    By mrphil in forum Wireless Networks
    Replies: 3
    Last Post: 5th October 2007, 08:34 AM
  4. Replies: 4
    Last Post: 14th May 2007, 01:01 PM
  5. testing network connection speed
    By projector1 in forum Wireless Networks
    Replies: 2
    Last Post: 10th October 2006, 11:48 AM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •