+ Post New Thread
Results 1 to 5 of 5
Hardware Thread, ERGO Secure desk in Technical; Hi all, We've invested a fair amount in the last 9 months in a fair few double ERGO secure desks. ...
  1. #1

    Join Date
    Oct 2006
    Location
    England
    Posts
    94
    Thank Post
    1
    Thanked 1 Time in 1 Post
    Rep Power
    0

    ERGO Secure desk

    Hi all,

    We've invested a fair amount in the last 9 months in a fair few double ERGO secure desks. We had the blanking plates fitted on the front, however the students have been prying these off with their fingers. Has anybody else had this problem? if so has anybody else approached Ergo and what have they said?

    Cheers

    Manick

  2. #2

    Join Date
    Oct 2009
    Posts
    156
    Thank Post
    9
    Thanked 12 Times in 12 Posts
    Rep Power
    13
    can we have a picture

  3. #3

    Join Date
    Oct 2006
    Location
    England
    Posts
    94
    Thank Post
    1
    Thanked 1 Time in 1 Post
    Rep Power
    0
    You can if you want but why would you want a picture?, the plates are about 6" by 2" and held in place by a small bolt to a nut that has been pressed into the face, however it pulls out very easily!!

    No-one else had the same problem then?

  4. #4

    Join Date
    Nov 2006
    Location
    Kendal
    Posts
    1,555
    Thank Post
    112
    Thanked 177 Times in 144 Posts
    Rep Power
    72
    We've got some secure desks but haven't had that issue. We have had an issue with some of the cabling and things and I have to say Ergo were fantastic. They came out and had a look and decided to do some modifications. They did this the next week and put an engineer on site for the day to tidy up all the little niggles.

    I would certainly drop them a line and see what they say. I couldn't have been happier with the way the handled our problems.

  5. #5

    Join Date
    Oct 2006
    Location
    England
    Posts
    94
    Thank Post
    1
    Thanked 1 Time in 1 Post
    Rep Power
    0
    I used a spring balance to measure how much pressure was needed to pull one of the screws out and it was only 2 to 2.5KG, so to pull one of the plates out only about 10pounds of pressure was needed, which is nowt. We have now resorted to using self tapping screws to stop the front being pulled off.

    Cheers

    manick
    Last edited by manick; 10th March 2010 at 03:27 PM.



SHARE:
+ Post New Thread

Similar Threads

  1. Ergo Secure desks
    By pbed77789 in forum Hardware
    Replies: 5
    Last Post: 16th September 2010, 03:27 PM
  2. Replies: 6
    Last Post: 13th April 2009, 07:29 PM
  3. Ergo... Any good?
    By ranj in forum Recommended Suppliers
    Replies: 5
    Last Post: 18th March 2009, 04:15 PM
  4. Ergo Free2Teach
    By CommodoreS in forum Network and Classroom Management
    Replies: 7
    Last Post: 18th March 2009, 04:14 PM
  5. ERGO
    By Andie in forum Bad Experiences
    Replies: 11
    Last Post: 25th February 2009, 01:32 PM

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •